Howdy, Stranger!
It looks like you're new here. If you want to get involved, click one of these buttons!
Categories
- All Discussions27,119
- Orphaned Marques
- ↳ Hudson21,185
- ↳ Street Rods805
- ↳ Off Topic564
- ↳ American Motors149
- ↳ Kaiser - Frazer70
- ↳ Nash71
- ↳ Packard163
- ↳ Studebaker121
- Classic American Cars
- ↳ Ford Motor Company959
- ↳ Chrysler Corporation478
- ↳ GM Corporation1,394
- ↳ Post War Chevrolets75
- ↳ Pontiac Forum119
- General
- ↳ All makes1,961
- ↳ Poll Discussions24
- Swapmeets & Events
- ↳ Events130
- ↳ Swapmeets108
- Hot Rod Corner
- ↳ Ford Rods90
- ↳ Lead Sleds67
- Special Interest Groups
- ↳ The Flathead Forum139
- European marques
- ↳ MG Car Company2
- ↳ Mercedes-Benz2
In this Discussion
- 1951hornethardtop January 28
- 48Sed January 30
- Kdancy January 28
- Ken U-Tx January 29
- MikeWA January 28
- Oldfarmer1947gmailcom January 29
- Tallent R January 28
- walts garage-53 January 29
Twin H
-
What carbs are used on the wide262 with a Twin H set-up,is the manifold the the same as the 308?
-
No, the bolts holding the carbs on are closer together on the 262 manifolds. Sorry I cant give you the numbers of the carbs tonight. I have a 262 with twin- H on a car stored for the winter about 5 miles from me and we are currently in an ice storm. I know there are others out there that have this info. I will look and get back to you later if someone doesnt get you the info.
-
What is the casting number of the correct manifold for the later 262?
-
307514 is a 1954 number for "262 Twin -H . However there are a lot of manifolds floating around that may be the exact same with a number thats not in any book. No one seems to know how this happened but it just did. So if you have one you think may fit , fit it up there and see . You may get a pleasant surprise,
RogerRetired Tech. -
So the #307183 would be for the Hornet 308 engine due to the different carbs used?
-
That number is in the book as for 308 with Twin -H , yes
RogerRetired Tech. -
The only difference between a 308 and a 262 intake twin H manifold is the bolt pattern that bolts the carb to the manifold. 262 is narrow and the 308 is wider. Walt.
-
And I have a 262 twin H manifold to get rid of, if anyone's interested. I think I paid 50 bucks for it and would be happy to get that out of it, plus shipping. I thought they were all the same when I got it- and the 308 car it was for is gone. Need to start getting rid of some of this stuff.
-
From what I can find the correct carb is # WA-1 2114s?
-
Mike, message sent--
-
You can also use 990s. Walt
-
What would two them cost,the 2114s or the 990s?
-
The following pictures are of a Wasp i.e. a 232 or 263 Twin H as well as a two pictures showing the difference in carburetor base plate mounting bolt spacing. The narrow spacing is for the Wasp and the wider for the Hornet twin H manifold. The carburetors used on the 232/262 twin H are WA1 990S - 2114S shown in the scan of the Carter manual. Note the casting number on the manifold for reference.
Wasp Twin H.jpg640 x 480 - 63K
Wasp Twin H4.jpg640 x 480 - 61K
Wasp Twin H3.jpg640 x 480 - 63K
Wasp Twin H2.jpg640 x 480 - 63K
2114S.JPG818 x 384 - 98KOldfarmer1947@gmail.com -
If you find 2 of either one, remember they have to be rebuilt to make sure that they have the correct metering rods and main jets and all adjustments are correct. Walt.
-
Walt
Is one of the mentioned carbs better than the other? and what is the tubing used for that I see attached to the end of the balance tube on some installations? -
The original carbs for the 1952-53 308 w/ Twin H were 968S, 1952-53 262 were 990S, and then the 1954 262 Twin h used 2114S, the 1954-56 308 Twin H used 2113S. The 2113S & 2114S were jetted & metered for better economy and power than the earlier 968S & 990S.
-
Thanks for the info on this as I am finding there is a lot to learn.
