ClassicCar

Ray

Any interest, please email me at kada9528@cox.net assorted parts are mostly for step downs, I don't know year of bucket headlight which probably is around 1930's, sold two air clearners...

Ray

[attachment=13550]IMG_0021.JPG[/attachment]

[attachment=13549]IMG_0020.JPG[/attachment]

[attachment=13548]195652Hornets008Small.jpg[/attachment]

[attachment=13547]195652Hornets006Small.jpg[/attachment]

[attachment=13546]56Hornet1Small.jpg[/attachment]

Kdancy

Location?

schillaz

Ray is located in Las Vegas.

dave11

Looking for a 262 cast iron head. Drivers door armrest (brown). Exhaust manifold 308 Twin H or single carb. Front bumper horse collar grill. All for a 52 Hornet sedan

Ol racer

Hello,

Could you describe some parts out of sight in the cases
Thanks

Ray

[attachment=13559]pickuptubespareparts006Small.jpg[/attachment]

[attachment=13558]pickuptubespareparts005Small.jpg[/attachment]

[attachment=13556]AssortedParts3.jpg[/attachment]

[attachment=13555]AssortedParts4.jpg[/attachment]

[attachment=13554]AssortedParts2.jpg[/attachment]

[attachment=13553]AssortedParts.jpg[/attachment]
Hi,

Generators, starter motor, starter motor drives, carbs, looks like rebult double action fuel pump, manifold, 262 cast iron and 308 alunimin heads, couple of carberator rebuild kits, chrome & stainless trim pieces, 52/53 pork chops, taillight and directional bezels, older hub caps, water pumps, parts are located in Las Vegas shop.

Ray

lsfirth

Are the door sill plates for a coupe by chance? If so, let me know what you want for a pair through a PM...

Thanks,
Lee

Ray

Dear Lee,

Yes I know one pair I took off my '52 Hornet is for a coupe, (must check other set again) however I already offered to Dan in N.D., if he doesn't want them I will immediately contact you.

Sorry,

Ray

Ray

Good Morning Dave,

See below email with pictures, I believe I have some of the items required and will take pictures and post on future email.

Good Luck,

Ray

Richards.

What are you asking for the 56? And does it run? How about the floor boards?
rich

lsfirth

Ray wrote:

Dear Lee,

Yes I know one pair I took off my '52 Hornet is for a coupe, (must check other set again) however I already offered to Dan in N.D., if he doesn't want them I will immediately contact you.

Sorry,

Ray

Hi Ray, Dan PM'd me and indicated he would pass on those. Send me a PM and if they aren't gold plated, I'm sure we can reach a deal :-)

Thanks again,
Lee

Ray

Needs restoration...Floors look okay, its a desert CA car or least that's where it was registered last...Doesn't run...Paid $1,750.- make me an offer...

Ray

Ray

Lee, mistakenly polished one pair which took paint off, then purchased a used very nice pair, then I decided to purchase pair from Doorsills LLC in New Jersey, therefore I have two coupe pairs; see picture. Make me reasonable offer...

Ray
[attachment=13572]CoupeDoorSills.jpg[/attachment]

lsfirth

Ray...just sent you a PM...

Thanks,
Lee

Ray

Good Morning Lee,

Having trouble recieving your PM message, please re-send directly to kada9528@cox.net

Thanks,

Ray

J Lombard

Ray you mentioned that you had a set of '52/'53 pork chops could you describe the condition & how much you're askinf?

regards

J Lombard

hudsoncustom

Ray / Lee.

I could use a set of those coupe / brougham sills too. Let me know if either wind up being available. I just cleaned up my Brougham sills, and they're quite a bit worse than I thought, so now I'm on the hunt for a nice set.

Ray - you mentioned you bought a pair from Doorsills LLC in NJ. Do they make new ones? If so, do you have the contact info for them?

Thanks.
Keith

Ray

hudsoncustom wrote:

Ray / Lee.

I could use a set of those coupe / brougham sills too. Let me know if either wind up being available. I just cleaned up my Brougham sills, and they're quite a bit worse than I thought, so now I'm on the hunt for a nice set.

Ray - you mentioned you bought a pair from Doorsills LLC in NJ. Do they make new ones? If so, do you have the contact info for them?

Thanks.
Keith

Good Morning Keith, See following address information:
"Aircraft Components Manufacturers · 302 Legion Place Haledon, NJ
Door Sills. Phone: (973) 904-0270. Our records show it was established in 2001 and incorporated in New Jersey."
No web-site, you'll have to learn about your order requirements, yes they make new door sills are hand made, for my coupe I paid $260.- but guy is busy and took 18 months before I recieved. Quality is good, however black diamonds and Hudson are not/indented/stamped on like original factory; they are stenciled on sills. Ones in pictures; top pair was polished were original on my car, lower pair I purchased until new ones arrived.

Good Luck,

Ray

Ray

J Lombard wrote:

Ray you mentioned that you had a set of '52/'53 pork chops could you describe the condition & how much you're askinf?

regards

J Lombard

J.,

I have several pork chops all required chrome plating, when I visit where car is I'll take pictures and post, if you like them you can make me an offer with postage. You may know already, efore he passed Bill Albright used to make sets of which many years ago I purchased at Laughlin Hudson Meet, I think I paid $250.-? They are a little heavy but look nice.

Ray

Ray

dave11 wrote:

Looking for a 262 cast iron head. Drivers door armrest (brown). Exhaust manifold 308 Twin H or single carb. Front bumper horse collar grill. All for a 52 Hornet sedan

Dave,

Haven't decided on restoring 1956 with Twin-H if so, as back up I may keep 262 cast iron head, will sell 308 aluninim head. Manifold is intake, no front bumper collar grill; do have single bumperette, have many carbs.

Good Luck,

Ray

hudsoncustom

Ray,

Thanks for the contact info. I can't wait 18 months, I'm putting interior in my car now. ha ha!

I'd be interested in purchasing the lower ones in the picture if they are still available. I know Lee wanted a pair, so he's got first dibs.

Let me know. You can email me at hudsoncustom at hotmail.com

Thanks
Keith

ClassicCar

Howdy, Stranger!

Categories

In this Discussion

We'd love to hear from you! info@classiccar.com