Howdy, Stranger!
It looks like you're new here. If you want to get involved, click one of these buttons!
Categories
- All Discussions27,065
- Orphaned Marques
- ↳ Hudson21,134
- ↳ Street Rods807
- ↳ Off Topic574
- ↳ American Motors149
- ↳ Kaiser - Frazer70
- ↳ Nash70
- ↳ Packard163
- ↳ Studebaker122
- Classic American Cars
- ↳ Ford Motor Company956
- ↳ Chrysler Corporation477
- ↳ GM Corporation1,396
- ↳ Post War Chevrolets75
- ↳ Pontiac Forum119
- General
- ↳ All makes1,960
- ↳ Poll Discussions24
- Swapmeets & Events
- ↳ Events130
- ↳ Swapmeets108
- Hot Rod Corner
- ↳ Ford Rods90
- ↳ Lead Sleds67
- Special Interest Groups
- ↳ The Flathead Forum139
- European marques
- ↳ MG Car Company2
- ↳ Mercedes-Benz2
In this Discussion
- billjharris May 2006
- jsrail May 2006
- rambos_ride May 2006
- Ray May 2006
48-49 Pieces Wanted for Customization
-
I won't be ready $$-wise to buy anything for a few weeks yet - but I thought I would put a feeler out there for a couple of parts I am needing for additional customizations for the 49 Project so I don't need anything perfect but don't want junk either...
1 - Dashboard, I only need the main shell and not anything else - and I will be cutting it up so if that's a problem don't sell it to me
2 - Entire upper rear seat from a Commodore. Should be 3 pieces 1-left, 1-right and 1-center flip down console - and I will be cutting them up so if that's a problem don't sell it to me [A Long Time Ago someone on the forum had a center rear console section but I didn't have the cash...maybe you still have it and the other 2 pieces?]
Anyway - that's it for now and no hurry...yet... -
For what I need I do not think so - if I can find my body and parts manual somewhere it would tell me if the parts are the same...do you have an extra and/or pics?jsrail wrote:Dan, does the dash have to be from a Commodore?
Jay -
rambos_ride wrote:I won't be ready $$-wise to buy anything for a few weeks yet - but I thought I would put a feeler out there for a couple of parts I am needing for additional customizations for the 49 Project so I don't need anything perfect but don't want junk either...
1 - Dashboard, I only need the main shell and not anything else - and I will be cutting it up so if that's a problem don't sell it to me
2 - Entire upper rear seat from a Commodore. Should be 3 pieces 1-left, 1-right and 1-center flip down console - and I will be cutting them up so if that's a problem don't sell it to me [A Long Time Ago someone on the forum had a center rear console section but I didn't have the cash...maybe you still have it and the other 2 pieces?]
Anyway - that's it for now and no hurry...yet...
Dan,
I may not be re-using my entire interior (believe you only need upper rear three piece back, which I have from '52 Hornet) a.) no problem with me if you cut b.) I'm not in hobby to make money, maybe we can barter your hood set/trunk set up for rear upper back seats? Example, today I traded my 308 engine/transmission, radiator, driveshaft and 308 unused head gasket for sun visor, pair of fender skirts, little chrome trim and forty dollars, I believe both buyer and seller are happy. Obviously seats need upholstery, however they are there with proper framework.
Ray -
Is there any hudson street-rodders going to make the Nashville car event june 23-24-25th?
I attended the NSRA springfield Missouri event last week end and a 34 or 35 hudson coupe made one of the top 25 cars out of 2200+ entries, I intended to get a pix to post here and my camera mal-functioned.
