Find A Classic Car
Thousands of listings here >>
sell your classic car
FREE to list - Online until sold

Howdy, Stranger!

It looks like you're new here. If you want to get involved, click one of these buttons!

Sign In Apply for Membership

Categories

In this Discussion

'Low' horn not sounding
  • Roger HarmonRoger Harmon
    Posts: 201Gold Member
    My new Hornet only toots the high tone horn. The low one gets power, and has a good ground, but will not sound. Any suggestions? Has anyone fixed one like this?

    R/ Roger.
    R/ Roger.
  • Roger HarmonRoger Harmon
    Posts: 201Gold Member
    Here it is.
    New Hornet1.jpg
    960 x 720 - 274K
    R/ Roger.
  • RL ChiltonRL Chilton
    Posts: 3,456Platinum Member
    Roger-

    That's not a horn, that's a car, '54 at that.
    Russell

    http://www.52hornetvert.blogspot.com
  • Chris SmithChris Smith
    Posts: 139Expert Adviser
    Some would say you want to TOOT YOUR OWN HORN. Regardless, you can try removing the dome cover and clean the contacts inside.
  • Uncle JoshUncle Josh
    Posts: 1,860Platinum Member
    And then you'll have to adjust the screw that determines how tight the contacts are until it toots properly.

    There once was a tutor who tooted,
    And tutored two tooters to toot,
    Said the two to the tutor,
    Is it easier to toot,
    Or to tutor two tooters to toot?
  • hotrodman2010hotmailcomhotrodman2010hotmailcom
    Posts: 110Hitchhiker
    I had just last week the very same issue with the low tone horn?????? I took it all apart and fiddled with it ,cleaning, adjusting, to no avail. I just replaced it with one off of a parts car even though they are differant make horns. have too many other issues to deal with at the moment and will re-address this later as they both toot know. Very nice sound be the Hudson horn!
  • Club Coupe
    Posts: 206Gold Member
    I had the same problem a while back and here's what I did. I started with the contacts under the horn button by spraying them liberally with contact cleaner. Then I did the same thing to the hot wire going to the horn itself, after taking the wire off of the horn. Finally I sprayed the contacts inside the horn. On about the third or fourth tap on the horn ring it worked. I used the straight contact cleaner (no lubrication) from Radio Shack.
  • Roger HarmonRoger Harmon
    Posts: 201Gold Member
    I'll give messing with the contacts inside the horn a try; does the dome cover just pry/pop off?
    R/ Roger.
  • Club Coupe
    Posts: 206Gold Member
    Roger:
    Twist it a tad bit counter clockwise and it should come right off. Hope the cleaner does the job for you.
  • Roger HarmonRoger Harmon
    Posts: 201Gold Member
    It did! I backed off the adjustment and emery'd the contact point, the had a helping hand toot while I adjusted the sound. Perfect!

    Thanks to all! R/ Roger.
    R/ Roger.
  • hoggyrubberhoggyrubber
    Posts: 477Gold Member
    glad to read this, none of mine work- so i'm going to give this a try.
  • hoggyrubberhoggyrubber
    Posts: 477Gold Member
    i'm glad you guys brought this up. i took mine apart today and cleaned the points and adjusted it and it works! thanks again.
  • Roger HarmonRoger Harmon
    Posts: 201Gold Member
    Yeay!
    R/ Roger.
Add a Comment
ClassicCar

Thousands of Classic Cars for Sale - Free to List.

Since 1996 we're been the place to go to for all things Classic Car. Classifieds, news, events, community and so much more. No clutter. No hassles. Just Classic Cars.

We'd love to hear from you! info@classiccar.com

Copyright 2011-2013 Classic Car
All rights reserved.

We accept no responsibility for inaccuracies. All trademarks acknowledged.